IDentiTech offers an extensive range of plastic card accessories. We stock most standard items.Custom printed items are our specialty and our prices are set to please.
If you do not see your preferred item shown below, simply contact us and we will assist.
Flexible Vinyl Pouches
This credit-card sized pouch has an adhesive back and will stick (non-permanently) to book covers, diaries or even clothing. It can also be used on the backs of chairs for place-settings. Measures: Outer 60mm x 93mm Insert: 54mm x 86mm
FVCH01 – economy range
A low-priced card pouch ideal for conferences or short-term use.
Measures: Outer 110mm x 68mm Inner 86mm x 60 mm. Available in horizontal. Measures: Outer 82mm x 95mm Inner 60mm x 86mm
FVCH21 – standard range
A durable clear pouch. The card is secured by a chain, lanyard or clip since the plastic is the same length on both sides. Measures: Outer 115mm x 72mm Inner 95mm x 63mm
FHCH22 is the horizontal equivalent. Measures: Outer 78mm x 100mm Inner 60mm x 90mm
FVCH71 – standard range
This durable pouch features a thumb-notch for easier card removal. Has a frosted backing with clear front panel. Measures: Outer 115mm x 63mm Inner 86mm x 54mm. FHCH72 is the horizontal equivalent. Measures Outer 77mm x 90mm Inner 54mm x 86mm.
FVCH11 – premium range
The highest-quality flexible pouch in our range is extra-soft and made to last. Holds a single card or single clamshell prox card. Measures: Outer 66mm x 111mm, Inner 58mm x93mm. FHCH12 is the horizontal equivalent. Measures: Outer 100mm x 78mm Inner 92mm x 63mm.
FHCHN10 – large conference pouch
For events which require a small program, name or ID card and a category identifier such as sponsor or exhibitor, this is the ideal pouch. We can supply the coloured category insert strips as well as print them to your instruction. Measures: Outer 180mm x102mm Inner 125mm x 95mm + 60mm x 95mm + 20mm x 95mm
RCCH01 – single holder
Suitable for a single standard plastic card. It features an optional clip or a strap clip or lanyard can be added. Cards can be displayed vertically or horizontally, open-faced. Colours: black, blue, white, red, grey & opaque
RCD01K – single holder
This single card holder is open-faced and displays cards as either vertical or horizontal. It will hold a single standard plastic card but unlike RRCH01 it has a solid back. Colours: black only
RCD02K – double sided holder
An open-faced card holder that can be hung vertically or horizontally, RCD02K holds one standard plastic card on one side and up to two standard plastic cards on the reverse. Or, it can hold a clamshell prox card on the reverse. Colours: black, blue, white, red, grey, opaque
RCHM01 – multicard holder
This open-faced holder can accommodate up to 5 standard plastic cards on one side, or one clamshell prox with three cards, or two clamshells and a single plastic card. Cards can be displayed either horizontally or vertically. Colours: black and opaque
RRCH01 – thumbslot holder
A closed-faced single card holder which protects the front and the back of the card. This holder has a clear finish so the card remains visible at all times. A cut-out at the back means cards or prox cards can be easily removed and replaced after scanning or reading. RRCV01 is the vertical equivalent.
KRCH45 – fuel card holder
This holder is closed-faced with a small cut-out to remove the card. It includes a key ring on a short chain.
Clips, Magnetic Bars & Hole Punchers
SCCL01 – strap clip
A 60mm vinyl strap with press-stud closer and alligator clip
SCCLP01 – strap clip with pin
A 60mm vinyl strap with press-stud closer, alligator clip with a safety pin
SCCLA01 – adhesive clip
This alligator clip with a pin has an adhesive back which peels off and can be stuck to the reverse side of a plastic card when a hole or slot is not wanted.
BCHA01 – bead chain adaptor
Made specifically for neck chains, this vinyl strap fits over the bead chain with a press-stud closer so cards or other holders can be added.
MGBAR01 – magnetic holder
This two-piece magnetised holder has an adhesive backing on one side which attaches to a card or flat surface. The other side lines up with the adhesive bar and the magnet holds the card in place. An alternative to putting pin holes or alligator teeth into clothing or to avoid punching a slot or hole into a card.
SLHP03 – slot/hole punch
An ideal item to put slots, holes or corners into a plastic card. The punch sits flat on a desktop and only requires light pressure to punch through the card. It comes complete with a guide so that the holes are always uniform/central. A handy seal at the base of the punch catches the off-cuts. It will last for thousands of cards.
MRR01K – Mini reel
This popular small reel has a belt clip on the back for attaching to clothing. A reinforced strap takes the ID card, pouch or holder. Available in a range of solid or translucent colours. Cord length 40cm.
MRC01K – Carbineer reel
A strong top latch attaches this reel onto clothing where a belt-clip is not considered secure enough. Available in a range of colours including: black, blue, red, green, orange and clear. Cord length 45cm.
MRH01S – heavy duty reel
Made of metal, this 25mm diameter reel comes with different end hooks. Choose from split ring or strap clip. It has a belt clip on the reverse and is preferred by hospitals where infection-control is paramount. Cord length 51cm.
- Fabric widths in 12mm tubular, 15mm flat, 20mm flat, 25mm flat
- Full-colour custom-printing
- Nylon, polyester and ribbon fabric available
- Variety of end hooks: swivel, alligator, carbineer, mobile phone, split ring etc
- Large range of stock colours or we can print to your PMS
- Safety break-away included
- Sample image provided before production
- Minimum order only 50
- No separate artwork charge
- Illustrator or jpeg files accepted
Standard end hooks with a greater range available.